View source for 616.12 Work Zone Speed Limits

MoDOT has the authority to set speed limits on the state highway system. This power extends to establishing speed limits in temporary traffic control zones, where the speed limit may be reduced from the normal speed limit for safety purposes.  Work zones shall be designed to the normal posted speed limit.

A reduced speed limit should be carefully considered before it is imposed, as motorists will only reduce their speed if they perceive a need to do so. Any decision to reduce the speed limit based on an arbitrary, "across the board" or other inappropriate rationale may result in non-compliance with the reduced speed limit by motorists and a false sense of security for workers. 

Should a reduced speed limit be deemed appropriate, the following table shows the recommended maximum speed reductions that may be imposed in temporary traffic control zones. 
===<center>Table 616.29 Recommended Maximum Speed Reductions</center>===
{| border="1" class="wikitable" style="margin: 1em auto 1em auto"
|+ 
! style="background:#BEBEBE" width="300"|Activity (i.e. Workers, Equipment or Material) Location !! style="background:#BEBEBE" colspan="2" width="300"|Recommended Work Zone Speed Reduction (When Applicable)
|-
|width="320"|10 ft. beyond edge of travelway to edge of right of way||width="300" align="center"|No speed reduction 
|-
|width="320"|In traffic lane or within 10 ft. of the traffic lane||align="center" width="300"| 10 mph
|-
|width="320"|Head-to-head on multilane||align="center" width="300"| 10 mph 
|-
|width="620" colspan="2"|Special circumstances within a temporary traffic control work zone may warrant a lower speed limit than recommend above. All speed limit reductions greater than 10 mph shall be documented, submitted to and approved by the District Work Zone Coordinator.
|}

After selecting a reduced speed limit based upon the table above, the following guidelines will assist in the proper installation and application of that reduced speed limit in the temporary traffic control zone. 

:* On divided highways, the reduced speed is applicable to the affected direction of travel only. 
:* Existing SPEED LIMIT signs within the temporary traffic control zone shall be covered or removed. 
:* SPEED LIMIT signs indicating the normal speed limit should be installed at the end of the reduced area provided no other reduction is imposed within the next one-half mile or no existing SPEED LIMIT sign is located within the next one-half mile. 
:* Reduced speed limit signing shall be removed, covered or turned from traffic when conditions requiring the reduced speed no longer exist.
:* For two-lane roadways, normal SPEED LIMIT signs are typically installed opposite the work zone SPEED LIMIT sign on the opposite approach facing traffic leaving the work zone. 
:* Reduced SPEED LIMIT signs are not to be installed on side street approaches or ramps for work limited to main line only. Reduced SPEED LIMIT signs may be installed downstream from the ramp or side street to inform drivers of the work zone speed limit. If the work is on the ramp, or affects the ramp, reduced SPEED LIMIT signs are to be used.
:* Posted work zone speed limit shall not be below 35 mph, except when local ordinance provides for a lower speed. The lower speed shall be used when applicable. 
:* Appropriate warning signs with advisory speed plaques should be used to advise of any specialized situations (i.e., temporary bypass, narrow lanes, etc.).
:* For approved speed reductions greater than 10 mph, additional notification should be provided through the use of the SPEED LIMIT XX AHEAD sign. Refer to [[#616.29.3 Work Zone SPEED LIMIT Figures|EPG 616.29.3 Work Zone SPEED LIMIT Figures]].
:* For approved speed reductions greater than 20 mph, the speed limit should be reduced in two stages. Refer to [[#616.29.3 Work Zone SPEED LIMIT Figures|EPG 616.29.3 Work Zone SPEED LIMIT Figures]].

==616.29.1 WORK ZONE FINE Sign (CONST-3A)==

The WORK ZONE FINE sign shall be specified on projects where all the following criteria are met: 
:* Duration of the work zone is longer than 4 hours. 
:* Reduced speed limits are in effect. 
:* Normal posted speed limit is 60 mph or greater. 
:* Workers will be present without positive protection (concrete barrier or guardrail). 

If a lane closure is used on a roadway with two lanes in the direction of travel, two DO NOT PASS and two PASS WITH CARE signs and two CONST-3X, (SPEEDING/PASSING) plates shall be specified. WORK ZONE plaques shall be specified for all DO NOT PASS and PASS WITH CARE signs being used as part of the work zone signing sequence. If a lane closure is used on a roadway with three or more lanes in the direction of travel, the DO NOT PASS and PASS WITH CARE signs and SPEEDING/PASSING plates shall not be specified.

==616.29.2 Sign Descriptions and Applications==

Sign descriptions and applications are located in [[616.2 Work Zone Signing and Applications|EPG 616.2 Work Zone Signing and Applications]].  

==616.29.3 Work Zone SPEED LIMIT Figures==
{|style="border:4px solid #ff9933; background:#f5f5f5" align="right"
|-
|[[media:616.29.3.1.pdf|pdf. version of Fig. 616.29.3.1]]
|-
|}
===Fig. 616.29.3.1 Work Zone SPEED LIMIT Locations within Advance Warning Area===
====<center>''Table 616.29.3.1''</center>====
{| border="1" class="wikitable" style="margin: 1em auto 1em auto" style="text-align:center"
|+ 
! style="background:#BEBEBE" rowspan="2" | Speed!! style="background:#BEBEBE" colspan="2"|Sign Spacing (ft.) !! style="background:#BEBEBE" colspan="2"| Taper Length (ft.)!!style="background:#BEBEBE" rowspan="2"|Optional Buffer Length, B (ft.)!! style="background:#BEBEBE" colspan="2"|Channelizer Spacing (ft.)
|-
! style="background:#BEBEBE" |Undivided, S!! style="background:#BEBEBE"|Divided, S!! style="background:#BEBEBE"|Shoulder, T1 !! style="background:#BEBEBE"|Lane, T2 !! style="background:#BEBEBE"| Tapers!! style="background:#BEBEBE"|Buffer/Work Areas
|-
|0 - 35 || 200 || 200 || colspan="5" rowspan="7" style="background:#ffffcc"|This typical application provides guidelines for the sequencing and location of work zone speed limit signs. Review appropriate typical applications for signs, sign spacing, taper length, buffer length, channelizer spacing, TMAs, channelizers, etc.
|-
|40 || 350 || 500 
|-
|45||350||500
|-
|50 - 55 || 500 || 1000 
|-
|rowspan="3"|60 - 70 ||colspan="2"| SA: 1000 
|-
|colspan="2"|SB: 1500
|-
|colspan="2"|SC: 2640
|}


[[image:616.29.3.1.jpg|right|580px]]






For speed limit guidance, refer to [[#Table 616.29 Recommended Speed Reductions|EPG 616.29 Work Zone Speed Limits]].

This typical application may be appropriate for single location work, per example, bridge work, culvert repair, localized pavement repair.

This typical application may be appropriate for work zone that may require a decrease of speed
throughout the entire work zone, per example, head-to-head on multilane applications.

(1) WO3-5 (SPEED LIMIT XX AHEAD). This sign is used when the approved speed reduction for an immediate location is greater than 10 mph below the existing or posted speed limit.

(2) The SPEED LIMIT sign may be moved upstream, if the district deems the work zone requires
advance speed limit notification.

For undivided roadways, provide signs only on the right side of each direction.

Reduced speed limit signing shall be removed, covered, or turned from traffic when conditions
requiring the reduced speed no longer exist.




































{|style="border:4px solid #ff9933; background:#f5f5f5" align="right"
|-
|[[media:616.29.3.2.pdf|pdf. version of Fig. 616.29.3.2]]
|-
|}

===Fig. 616.29.3.2  Work Zone SPEED LIMIT Locations within Activity Area===
====<center>''Table 616.29.3.2''</center>====
{| border="1" class="wikitable" style="margin: 1em auto 1em auto" style="text-align:center"
|+ 
! style="background:#BEBEBE" rowspan="2" | Speed!! style="background:#BEBEBE" colspan="2"|Sign Spacing (ft.) !! style="background:#BEBEBE" colspan="2"| Taper Length (ft.)!!style="background:#BEBEBE" rowspan="2"|Optional Buffer Length, B (ft.)!! style="background:#BEBEBE" colspan="2"|Channelizer Spacing (ft.)
|-
! style="background:#BEBEBE" |Undivided, S!! style="background:#BEBEBE"|Divided, S!! style="background:#BEBEBE"|Shoulder, T1 !! style="background:#BEBEBE"|Lane, T2 !! style="background:#BEBEBE"| Tapers!! style="background:#BEBEBE"|Buffer/Work Areas
|-
|0 - 35 || 200 || 200 || colspan="5" rowspan="7" style="background:#ffffcc"|This typical application provides guidelines for the sequencing and location of work zone speed limit signs. Review appropriate typical applications for signs, sign spacing, taper length, buffer length, channelizer spacing, TMAs, channelizers, etc.
|-
|40 || 350 || 500 
|-
|45||350||500
|-
|50 - 55 || 500 || 1000 
|-
|rowspan="3"|60 - 70 ||colspan="2"| SA: 1000 
|-
|colspan="2"|SB: 1500
|-
|colspan="2"|SC: 2640
|}


[[image:616.29.3.2.jpg|right|580px]]






For speed limit guidance, refer to [[#Table 616.29 Recommended Speed Reductions|EPG 616.29 Work Zone Speed Limits]].

This typical application may be appropriate for moving operations when acitivities will
move along the travelway, per example, resurfacing projects, pavement repair, concrete overlay, pavement marking, etc.

This typical application may be appropriate for work zones with a stationary concern within a long activity area.

(1) If used, the WO3-5 (SPEED LIMIT XX AHEAD) sign shall be located in the Advance Warning Area.
This sign is used only when the approved speed reduction for an immediate location is greater than 10 mph below the existing or posted speed limit. For sign placement, refer to [[#Fig. 616.29.3.1 Work Zone SPEED LIMIT Locations within Advance Warning Area|
EPG 616.29.3.1 Work Zone SPEED LIMIT Locations Within Advance Warning Area]].

(2) The SPEED LIMIT signs should be located at the farthest upstream activity with
human presence.

For undivided roadways, provide signs only on the right side of each direction.

Reduced speed limit signing shall be removed, covered or turned from traffic when conditions requiring the reduced speed no longer exist.






















{|style="border:4px solid #ff9933; background:#f5f5f5" align="right"
|-
|[[media:616.29.3.3.pdf|pdf. version of Fig. 616.29.3.3]]
|-
|}

===Fig. 616.29.3.3 Work Zone FINE Sign and SPEED LIMIT Locations within Advance Warning Area===

====<center>''Table 616.29.3.3''</center>====
{| border="1" class="wikitable" style="margin: 1em auto 1em auto" style="text-align:center"
|+ 
! style="background:#BEBEBE" rowspan="2" | Speed!! style="background:#BEBEBE" colspan="2"|Sign Spacing (ft.) !! style="background:#BEBEBE" colspan="2"| Taper Length (ft.)!!style="background:#BEBEBE" rowspan="2"|Optional Buffer Length, B (ft.)!! style="background:#BEBEBE" colspan="2"|Channelizer Spacing (ft.)
|-
! style="background:#BEBEBE" |Undivided, S!! style="background:#BEBEBE"|Divided, S!! style="background:#BEBEBE"|Shoulder, T1 !! style="background:#BEBEBE"|Lane, T2 !! style="background:#BEBEBE"| Tapers!! style="background:#BEBEBE"|Buffer/Work Areas
|-
|0 - 35 || 200 || 200 || colspan="5" rowspan="7" style="background:#ffffcc"|This typical application provides guidelines for the sequencing and location of work zone speed limit signs. Review appropriate typical applications for signs, sign spacing, taper length, buffer length, channelizer spacing, TMAs, channelizers, etc.
|-
|40 || 350 || 500 
|-
|45||350||500
|-
|50 - 55 || 500 || 1000 
|-
|rowspan="3"|60 - 70 ||colspan="2"| SA: 1000 
|-
|colspan="2"|SB: 1500
|-
|colspan="2"|SC: 2640
|}


[[image:616.29.3.3.jpg|right|580px]]








For speed limit guidance, refer to [[#Table 616.29 Recommended Speed Reductions|EPG 616.29 Work Zone Speed Limits]].

This typical application may be appropriate for single location work, per example, bridge work, culvert repair, localized pavement repair.

This typical application may be appropriate for work zone that may require a decrease of speed
throughout the entire work zone, per example, head-to-head on multilane applications.

(1) WO3-5 (SPEED LIMIT XX AHEAD). This sign is used only when the approved speed reduction for an immediate location is greater than 10 mph below the existing or posted speed limit.

(2) The SPEED LIMIT sign may be moved upstream, if the district deems the work zone requires
advance speed limit notification.

Reduced speed limit signing shall be removed, covered, or turned from traffic when conditions
requiring the reduced speed no longer exist.

For undivided roadways, provide signs only on the right side of each direction.

































{|style="border:4px solid #ff9933; background:#f5f5f5" align="right"
|-
|[[media:616.29.3.4.pdf|pdf. version of Fig. 616.29.3.4]]
|-
|}

===Fig. 616.29.3.4 Work Zone SPEED LIMIT Locations for Reductions Greater than 20 mph and Reduction in Two Locations===

[[Image:628.3.4.jpg|center|790px]]

For undivided roadways, provide signs only on the right side of each direction. 

For proper speed limit sign spacing, reference typical applications [[#Fig. 616.29.3.1 Work Zone SPEED LIMIT Locations within Advance Warning Area|EPG 616.29.3.1 Work Zone Speed Limit Locations within Advance Warning Area]] or [[#Fig. 616.29.3.2 Work Zone SPEED LIMIT Locations within Activity Area|EPG 616.29.3.2 Work Zone Speed Limit Locations within Activity Area]].



[[Category:616 Temporary Traffic Control]]