1060.4 Laboratory Testing Guidelines for Sec 1060 - Revision history

Smithk: Per CM, removed archaic SiteManager info and replaced with AASHTOWARE info

2021-09-14T16:02:39Z

Per CM, removed archaic SiteManager info and replaced with AASHTOWARE info

← Older revision		Revision as of 11:02, 14 September 2021
Line 2:		Line 2:

	===1060.4.1 Procedure===		===1060.4.1 Procedure===
	The Laboratory tests to be performed on the sample are designated by the inspector in the remarks area of ~~SiteManager~~.		The Laboratory tests to be performed on the sample are designated by the inspector in the remarks area of AASHTOWARE Project (AWP).

	====Chemical Tests====		====Chemical Tests====
	The procedure for determining mass of zinc coating shall be according to AASHTO T65. Particular attention should be given as to whether both the inside and the outside surfaces have been galvanized. The stripping method shall be used in all cases where the area of the test specimen can be accurately calculated. On test specimens shaped so that the area cannot be calculated, the mass of coating shall be determined with a magnetic gage, in accordance with ASTM E376. Refer to [[:Category:1043 Fence Material#1043.2.2 Metal Posts, Brace Rails and Gate Frames\|Field determination of weight (mass) of coating]] for additional information on the proper use of the magnetic gage. Original test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through ~~SiteManager~~.		The procedure for determining mass of zinc coating shall be according to AASHTO T65. Particular attention should be given as to whether both the inside and the outside surfaces have been galvanized. The stripping method shall be used in all cases where the area of the test specimen can be accurately calculated. On test specimens shaped so that the area cannot be calculated, the mass of coating shall be determined with a magnetic gage, in accordance with ASTM E376. Refer to [[:Category:1043 Fence Material#1043.2.2 Metal Posts, Brace Rails and Gate Frames\|Field determination of weight (mass) of coating]] for additional information on the proper use of the magnetic gage. Original test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through AWP.

	===1060.4.2 Sample Record===		===1060.4.2 Sample Record===
	The sample record shall be completed in ~~SiteManager~~, as described in [[:Category:101 Standard Forms#Sample Record General ~~Information~~\| Sample Record General ~~Information]] [[image:bulldozer.jpg\|20px~~]], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[:category: 106 Control of Material#Reporting Test Results\|Reporting Test Results]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in AASHTOWARE Project (AWP), as described in [[:Category:101 Standard Forms#Sample Record, General\|AWP MA Sample Record, General]], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[:category: 106 Control of Material#Reporting Test Results\|Reporting Test Results]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

	[[Category:1060 Electrical Conduit]]		[[Category:1060 Electrical Conduit]]

Smithk: updated link

2016-06-15T18:36:57Z

updated link

← Older revision		Revision as of 13:36, 15 June 2016
Line 1:		Line 1:
	This article establishes procedures for Laboratory testing and reporting electrical conduit materials. Refer to [http://www.modot.~~mo.gov~~/business/standards_and_specs/~~Sec1060~~.pdf Sec 1060] for MoDOT’s specifications.		This article establishes procedures for Laboratory testing and reporting electrical conduit materials. Refer to [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=14 Sec 1060] for MoDOT’s specifications.

	===1060.4.1 Procedure===		===1060.4.1 Procedure===

Smithk: updated link

2013-08-22T17:12:03Z

updated link

← Older revision		Revision as of 12:12, 22 August 2013
Line 8:		Line 8:

	===1060.4.2 Sample Record===		===1060.4.2 Sample Record===
	The sample record shall be completed in SiteManager, as described in [~~http~~:~~//contribute.modot.mo.gov/business/materials/pdf/vol_3/AS3510~~.~~pdf Automation Section 3510~~], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[:category: 106 Control of Material#Reporting Test Results\|Reporting Test Results]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in SiteManager, as described in [[:Category:101 Standard Forms#Sample Record General Information\| Sample Record General Information]] [[image:bulldozer.jpg\|20px]], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[:category: 106 Control of Material#Reporting Test Results\|Reporting Test Results]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

	[[Category:1060 Electrical Conduit]]		[[Category:1060 Electrical Conduit]]

Smithk: /* 1060.4.2 Sample Record */ Per CM, updated link to AS 3510

2011-07-05T20:25:19Z

1060.4.2 Sample Record: Per CM, updated link to AS 3510

← Older revision		Revision as of 15:25, 5 July 2011
Line 8:		Line 8:

	===1060.4.2 Sample Record===		===1060.4.2 Sample Record===
	The sample record shall be completed in SiteManager, as described in [http://~~wwwi~~/~~intranet~~/cm/~~materials~~/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[:category: 106 Control of Material#Reporting Test Results\|Reporting Test Results]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in SiteManager, as described in [http://contribute.modot.mo.gov/business/materials/pdf/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[:category: 106 Control of Material#Reporting Test Results\|Reporting Test Results]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

	[[Category:1060 Electrical Conduit]]		[[Category:1060 Electrical Conduit]]

Smithk: article construction

2008-02-21T15:34:02Z

article construction

← Older revision		Revision as of 10:34, 21 February 2008
Line 8:		Line 8:

	===1060.4.2 Sample Record===		===1060.4.2 Sample Record===
	The sample record shall be completed in SiteManager, as described in [[Automation ~~Sec~~ 3510]], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[:category: 106 Control of Material#Reporting Test Results\|Reporting Test Results]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in SiteManager, as described in [http://wwwi/intranet/cm/materials/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[:category: 106 Control of Material#Reporting Test Results\|Reporting Test Results]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

	[[Category:1060 Electrical Conduit]]		[[Category:1060 Electrical Conduit]]

Smithk: moved article to its own page

2007-09-07T19:46:40Z

moved article to its own page

New page

This article establishes procedures for Laboratory testing and reporting electrical conduit materials. Refer to [http://www.modot.mo.gov/business/standards_and_specs/Sec1060.pdf Sec 1060] for MoDOT’s specifications.

===1060.4.1 Procedure===
The Laboratory tests to be performed on the sample are designated by the inspector in the remarks area of SiteManager.

====Chemical Tests====
The procedure for determining mass of zinc coating shall be according to AASHTO T65. Particular attention should be given as to whether both the inside and the outside surfaces have been galvanized. The stripping method shall be used in all cases where the area of the test specimen can be accurately calculated. On test specimens shaped so that the area cannot be calculated, the mass of coating shall be determined with a magnetic gage, in accordance with ASTM E376. Refer to [[:Category:1043 Fence Material#1043.2.2 Metal Posts, Brace Rails and Gate Frames|Field determination of weight (mass) of coating]] for additional information on the proper use of the magnetic gage. Original test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through SiteManager.

===1060.4.2 Sample Record===
The sample record shall be completed in SiteManager, as described in [[Automation Sec 3510]], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[:category: 106 Control of Material#Reporting Test Results|Reporting Test Results]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

[[Category:1060 Electrical Conduit]]