413.6 Scrub Seal Treatment - Revision history

Smithk: Per DE, restored slightly modified scrub seal guidance

2018-12-10T20:37:58Z

Per DE, restored slightly modified scrub seal guidance

← Older revision		Revision as of 15:37, 10 December 2018
Line 1:		Line 1:
	The scrub seal ~~treatment~~ is ~~no longer in use~~.		The scrub seal is a process by which an anionic charged polymer modified asphalt agent is applied to an asphalt pavement surface and scrubbed into the cracks and voids with a broom. A small layer of aggregate is then applied over the asphalt and then broomed once again, forcing the mix into the cracks and voids to form a seal. The seal is then rolled with a pneumatic tire roller. Since scrub seal is meant to be used as a preventive maintenance measure, its primary purpose is to fill cracks and seal an asphalt pavement.

			This process helps to prevent light deterioration, retard progressive failures, and reduce routine maintenance service activities. The traveled way can be opened to traffic about two (2) hours after application.

			Scrub sealing should be used only on pavements with AADT less than 7,500 and of sound condition. This process should be used only on stable pavements that are dry, oxidized, and cracked, since it is not intended to improve the structural condition of the pavement.




	[[Category:413 Surface Treatments and Preventive Maintenance\|413.06]]		[[Category:413 Surface Treatments and Preventive Maintenance\|413.06]]

Smithk: Per Maintenance, article info deleted since treatment is no longer in use

2014-12-02T20:55:42Z

Per Maintenance, article info deleted since treatment is no longer in use

← Older revision		Revision as of 15:55, 2 December 2014
Line 1:		Line 1:
	The scrub seal is a process by which an anionic charged polymer modified asphalt agent is applied to an asphalt pavement surface and scrubbed into the cracks and voids with a broom. A small layer of aggregate is then applied over the asphalt and then broomed once again, forcing the mix into the cracks and voids to form a seal. The seal is then rolled with a pneumatic tire roller. Since scrub seal is meant to be used as a preventive maintenance measure, its primary purpose is to fill cracks and seal an asphalt pavement.		The scrub seal treatment is no longer in use.

	Scrub sealing is less expensive per mile than a 1 in. hot mix overlay, chip seal, and microsurfacing. This process helps to prevent light deterioration, retard progressive failures, and reduce routine maintenance service activities. The traveled way can be opened to traffic about two (2) hours after application.

	Scrub sealing should be used only on pavements with AADT less than 7,500 and of sound condition. This process should be used only on stable pavements that are dry, oxidized, and cracked, since it is not intended to improve the structural condition of the pavement.

	~~==413.6.1 Maintenance Planning Guideline==~~
	~~'''Printable''' [[media:R315 - Scrub Seals.pdf\|'''Maintenance Planning Guideline for Scrub Seals''']].~~

	~~Index of all [[:Category:170 Maintenance Activity Planning Guidelines#Index of Printable Planning Guides\|Maintenance Planning Guidelines]].~~


	[[Category:413 Surface Treatments and Preventive Maintenance\|413.06]]		[[Category:413 Surface Treatments and Preventive Maintenance\|413.06]]

Smithk: minor clarification

2010-11-24T17:14:09Z

minor clarification

← Older revision		Revision as of 12:14, 24 November 2010
Line 3:		Line 3:
	Scrub sealing is less expensive per mile than a 1 in. hot mix overlay, chip seal, and microsurfacing. This process helps to prevent light deterioration, retard progressive failures, and reduce routine maintenance service activities. The traveled way can be opened to traffic about two (2) hours after application.		Scrub sealing is less expensive per mile than a 1 in. hot mix overlay, chip seal, and microsurfacing. This process helps to prevent light deterioration, retard progressive failures, and reduce routine maintenance service activities. The traveled way can be opened to traffic about two (2) hours after application.

	Scrub sealing should be used only on pavements with ~~ADT~~ less than 7,500 and of sound condition. This process should be used only on stable pavements that are dry, oxidized, and cracked, since it is not intended to improve the structural condition of the pavement.		Scrub sealing should be used only on pavements with AADT less than 7,500 and of sound condition. This process should be used only on stable pavements that are dry, oxidized, and cracked, since it is not intended to improve the structural condition of the pavement.

	==413.6.1 Maintenance Planning Guideline==		==413.6.1 Maintenance Planning Guideline==

EPG-Admin: Replace text with link to printable guide.

2009-07-29T19:34:35Z

Replace text with link to printable guide.

@@ Line 6: / Line 6: @@
 ==413.6.1 Maintenance Planning Guideline==
-{|style="padding: 0.3em; margin-left:15px; border:1px solid #a9a9a9; text-align:center; font-size: 95%; background:#f5f5f5" width="160px" align="right"
+'''Printable''' [[media:R315 - Scrub Seals.pdf|'''Maintenance Planning Guideline for Scrub Seals''']].
-The time and expenses incurred for spot or continuous seals using either hand or bar application of bituminous material and covering with aggregate material either by hand, tailgate or spreader. This includes course aggregate chip seals & fine aggregate chip seals.
+Index of all [[:Category:170 Maintenance Activity Planning Guidelines#Index of Printable Planning Guides|Maintenance Planning Guidelines]].
 [[Category:413 Surface Treatments and Preventive Maintenance|413.06]]

EPG-Admin at 16:30, 16 January 2008

2008-01-16T16:30:32Z

New page

The scrub seal is a process by which an anionic charged polymer modified asphalt agent is applied to an asphalt pavement surface and scrubbed into the cracks and voids with a broom. A small layer of aggregate is then applied over the asphalt and then broomed once again, forcing the mix into the cracks and voids to form a seal. The seal is then rolled with a pneumatic tire roller. Since scrub seal is meant to be used as a preventive maintenance measure, its primary purpose is to fill cracks and seal an asphalt pavement.

Scrub sealing is less expensive per mile than a 1 in. hot mix overlay, chip seal, and microsurfacing. This process helps to prevent light deterioration, retard progressive failures, and reduce routine maintenance service activities. The traveled way can be opened to traffic about two (2) hours after application.

Scrub sealing should be used only on pavements with ADT less than 7,500 and of sound condition. This process should be used only on stable pavements that are dry, oxidized, and cracked, since it is not intended to improve the structural condition of the pavement.

==413.6.1 Maintenance Planning Guideline==
{|style="padding: 0.3em; margin-left:15px; border:1px solid #a9a9a9; text-align:center; font-size: 95%; background:#f5f5f5" width="160px" align="right"
|-
|'''Code:''' R31C
|}
'''Definition'''

The time and expenses incurred for spot or continuous seals using either hand or bar application of bituminous material and covering with aggregate material either by hand, tailgate or spreader. This includes course aggregate chip seals & fine aggregate chip seals.

'''Purpose'''

To seal out surface moisture on cracked or deteriorating asphaltic surfaces, extend pavement life, and improve skid resistance.

'''Scheduling'''

When temperatures are 65° F and rising.

'''Recommended Equipment'''

*Truck Distributor
*Chip Spreader
*Optional Brooms
*Rubber Tire Roller
*Trucks
*Optional Pilot Truck
*Traffic Control Equipment (See [[616.23 Traffic Control for Field Operations|Traffic Control for Field Operations]])

'''Recommended Material'''

*Liquid Binder – Sealing Grades
Check with Materials Office for selection of aggregate size (3/16 in. or less).
*Sand – Other Blot Material

'''Recommended Procedure'''

1. Place traffic control devices as needed.

2. Sweep the existing surface to clean and remove loose debris.

3. Set temporary pavement marking.

4. Apply asphalt at recommended rate and broom as necessary.

5. Cover asphalt with blotting material.

6. Broom blotting material.

7. Roll with rubber tire roller.

8. Remove traffic control devices, except "Fresh Oil" and "No Center Stripe" signs, and open to traffic.

9. "Fresh Oil" and "Loose Gravel" signs should remain in place until surface is cured and loose aggregate has been thoroughly swept off.

'''Safety'''

Wear all appropriate PPE. Refer to [http://lnapp1/RI/RIManual.NSF/SHToC?OpenView Safety Policies, Rules & Regulations-Employee Handbook.]

'''Other Considerations'''

Clean up excess material with power broom.

'''References'''

Standard Specification [http://modot.mo.gov/business/standards_and_specs/Sec0413.pdf Sec 413.20] and [http://modot.mo.gov/business/standards_and_specs/Sec1015.pdf Sec 1015] and

{|
|[[Image:413.6 Scrub Seal1.jpg|400px]] || [[Image:413.6 Scrub Seal2.jpg|400px]]
|-
|text align="center"|'''Roadway Prior to Scrub Seal''' || text align="center"|'''Scrubbing the Oil into the Roadway'''
|-
|[[Image:413.6 Scrub Seal3.jpg|400px]] || [[Image:413.6 Scrub Seal4.jpg|400px]]
|-
|text align="center"|'''Oil Penetrates and Seals Cracks''' || text align="center"|'''Applying the Sand'''
|-
|[[Image:413.6 Scrub Seal5.jpg|400px]] || [[Image:413.6 Scrub Seal6.jpg|400px]]
|-
|text align="center"|'''Sand Applied Prior to Scrubbing''' || text align="center"|'''Scrubbing the Sand'''
|}

[[Category:413 Surface Treatments and Preventive Maintenance|413.06]]