626.3 Construction Inspection Guidelines for Sec 626 - Revision history

Smithk: Per TP, updated Major Highway System map

2022-06-03T13:16:30Z

Per TP, updated Major Highway System map

← Older revision		Revision as of 08:16, 3 June 2022
Line 23:		Line 23:
	*Shoulder thickness is less than 3 ¾ in.		*Shoulder thickness is less than 3 ¾ in.

	The edge marking strategies on [[media:144 Major Highway System ~~2021~~.pdf\|major roads]] shall be:		The edge marking strategies on [[media:144 Major Highway System 2022.pdf\|major roads]] shall be:

	1. Edgeline rumble strips - where shoulder thickness allows.		1. Edgeline rumble strips - where shoulder thickness allows.

Smithk: updated major highway system map

2021-06-04T15:47:54Z

updated major highway system map

← Older revision		Revision as of 10:47, 4 June 2021
Line 23:		Line 23:
	*Shoulder thickness is less than 3 ¾ in.		*Shoulder thickness is less than 3 ¾ in.

	The edge marking strategies on [[media:144 Major Highway System.pdf\|major roads]] shall be:		The edge marking strategies on [[media:144 Major Highway System 2021.pdf\|major roads]] shall be:

	1. Edgeline rumble strips - where shoulder thickness allows.		1. Edgeline rumble strips - where shoulder thickness allows.

Smithk: Per TS, minor clarification

2020-11-12T18:23:26Z

Per TS, minor clarification

← Older revision		Revision as of 13:23, 12 November 2020
Line 3:		Line 3:
	This article provides additional requirements for rumble strips that need to be implemented on all jobs, regardless if the requirements are specifically covered in the specifications in effect at the time of award of a contract.		This article provides additional requirements for rumble strips that need to be implemented on all jobs, regardless if the requirements are specifically covered in the specifications in effect at the time of award of a contract.

	'''Construction Requirements (for [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=9 Sec 626.2])''' Rumble strips and striping need to be installed according to [~~http~~://www.modot.~~mo.gov~~/~~business~~/~~standards_and_specs~~/documents/~~62600~~.pdf Standard Plan 626.00] and the guidelines below.		'''Construction Requirements (for [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=9 Sec 626.2])''' Rumble strips and striping need to be installed according to [https://www.modot.org/sites/default/files/documents/62600_0.pdf Standard Plan 626.00] and the guidelines below.

	The lateral deviation of rumble strips are not to exceed 1 inch in 100 ft. Milled rumbles are to be clean and dry before the installation of permanent pavement marking.		The lateral deviation of rumble strips are not to exceed 1 inch in 100 ft. Milled rumbles are to be clean and dry before the installation of permanent pavement marking.

Smithk: Updated Major Highway System map

2019-04-26T14:50:18Z

Updated Major Highway System map

← Older revision		Revision as of 09:50, 26 April 2019
Line 23:		Line 23:
	*Shoulder thickness is less than 3 ¾ in.		*Shoulder thickness is less than 3 ¾ in.

	The edge marking strategies on [~~http~~:~~//sharepoint/systemdelivery/TP/sysanlysis/dmas/Shared%20Documents/Maps/MajorHighwaySystem8302015~~.pdf major roads] shall be:		The edge marking strategies on [[media:144 Major Highway System.pdf\|major roads]] shall be:

	1. Edgeline rumble strips - where shoulder thickness allows.		1. Edgeline rumble strips - where shoulder thickness allows.

Kleins1 at 02:15, 3 December 2018

2018-12-03T02:15:28Z

← Older revision		Revision as of 21:15, 2 December 2018
Line 15:		Line 15:
	* Posted speed limit of 50 mph or greater.		* Posted speed limit of 50 mph or greater.

	* The shoulder should be new asphalt with a minimum thickness of 1 in. on top of ~~a solid~~ base.		* The shoulder should be new asphalt with a minimum thickness of 1 in. on top of an existing asphalt base.

	Shoulder rumbles strips should not be installed if any of the following conditions exist:		Shoulder rumbles strips should not be installed if any of the following conditions exist:

Kleins1 at 02:12, 3 December 2018

2018-12-03T02:12:52Z

← Older revision		Revision as of 21:12, 2 December 2018
Line 15:		Line 15:
	* Posted speed limit of 50 mph or greater.		* Posted speed limit of 50 mph or greater.

	* The shoulder should be new asphalt with a minimum thickness of 1 ~~3/4~~ in. on top of a solid base.		* The shoulder should be new asphalt with a minimum thickness of 1 in. on top of a solid base.

	Shoulder rumbles strips should not be installed if any of the following conditions exist:		Shoulder rumbles strips should not be installed if any of the following conditions exist:

Smithk at 13:57, 28 September 2018

2018-09-28T13:57:43Z

← Older revision		Revision as of 08:57, 28 September 2018
Line 33:		Line 33:
	4. An optional method of providing rumble strips is to provide a solid 2 ft. wide strip in the shoulder, 3 ¾ in. thick, where the rumbles can be milled.		4. An optional method of providing rumble strips is to provide a solid 2 ft. wide strip in the shoulder, 3 ¾ in. thick, where the rumbles can be milled.

	The location and pattern of full rumble strips shall be in accordance with [~~http~~://www.modot.~~mo.gov/business/standards_and_specs~~/~~documents~~/~~62600.pdf~~ Standard Plan 626.00].		The location and pattern of full rumble strips shall be in accordance with [https://www.modot.org/media/16900 Standard Plan 626.00].

Smithk: updated link

2016-06-09T15:36:12Z

updated link

← Older revision		Revision as of 10:36, 9 June 2016
Line 3:		Line 3:
	This article provides additional requirements for rumble strips that need to be implemented on all jobs, regardless if the requirements are specifically covered in the specifications in effect at the time of award of a contract.		This article provides additional requirements for rumble strips that need to be implemented on all jobs, regardless if the requirements are specifically covered in the specifications in effect at the time of award of a contract.

	'''Construction Requirements (for [http://www.modot.~~mo.gov~~/business/standards_and_specs/~~Sec0626~~.pdf Sec 626.2])''' Rumble strips and striping need to be installed according to [http://www.modot.mo.gov/business/standards_and_specs/documents/62600.pdf Standard Plan 626.00] and the guidelines below.		'''Construction Requirements (for [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=9 Sec 626.2])''' Rumble strips and striping need to be installed according to [http://www.modot.mo.gov/business/standards_and_specs/documents/62600.pdf Standard Plan 626.00] and the guidelines below.

	The lateral deviation of rumble strips are not to exceed 1 inch in 100 ft. Milled rumbles are to be clean and dry before the installation of permanent pavement marking.		The lateral deviation of rumble strips are not to exceed 1 inch in 100 ft. Milled rumbles are to be clean and dry before the installation of permanent pavement marking.

Smithk: updated link

2016-02-02T14:40:37Z

updated link

← Older revision		Revision as of 09:40, 2 February 2016
Line 23:		Line 23:
	*Shoulder thickness is less than 3 ¾ in.		*Shoulder thickness is less than 3 ¾ in.

	The edge marking strategies on [http://~~wwwi~~/~~intranet~~/tp/~~documents~~/~~Major_Highway_System~~.pdf major roads] shall be:		The edge marking strategies on [http://sharepoint/systemdelivery/TP/sysanlysis/dmas/Shared%20Documents/Maps/MajorHighwaySystem8302015.pdf major roads] shall be:

	1. Edgeline rumble strips - where shoulder thickness allows.		1. Edgeline rumble strips - where shoulder thickness allows.

Smithk: Per Transportation Planning, updated Major Highways map

2012-09-07T15:27:00Z

Per Transportation Planning, updated Major Highways map

← Older revision		Revision as of 10:27, 7 September 2012
Line 23:		Line 23:
	*Shoulder thickness is less than 3 ¾ in.		*Shoulder thickness is less than 3 ¾ in.

	The edge marking strategies on [~~[media~~:~~major highways~~.pdf\|major roads]] shall be:		The edge marking strategies on [http://wwwi/intranet/tp/documents/Major_Highway_System.pdf major roads] shall be:

	1. Edgeline rumble strips - where shoulder thickness allows.		1. Edgeline rumble strips - where shoulder thickness allows.