Category:1124 Sodium Chloride - Revision history

Smithk: Per CM, removed archaic SiteManager info and replaced with AASHTOWARE info

2021-09-17T13:06:26Z

Per CM, removed archaic SiteManager info and replaced with AASHTOWARE info

← Older revision		Revision as of 08:06, 17 September 2021
Line 29:		Line 29:
	==1124.3 Report==		==1124.3 Report==

	Sodium chloride sampled and submitted to the Laboratory will be reported in accordance with 1124.4 Laboratory Testing Guidelines. A ~~SiteManager~~ sample record shall be used for field reporting of sodium chloride. Invoice number or other identification as well as quantities, are to be shown. Loads that are not tested may be accepted on the basis of visual inspection at the discretion of the district Construction and Materials Engineer. All field reports shall include the last sample identification number under which the chemical composition was tested and accepted. The report is to indicate acceptance, or rejection. Appropriate remarks, as necessary, are to be included in the report to clarify conditions of acceptance or rejection.		Sodium chloride sampled and submitted to the Laboratory will be reported in accordance with 1124.4 Laboratory Testing Guidelines. A AASHTOWARE Project (AWP) sample record shall be used for field reporting of sodium chloride. Invoice number or other identification as well as quantities, are to be shown. Loads that are not tested may be accepted on the basis of visual inspection at the discretion of the district Construction and Materials Engineer. All field reports shall include the last sample identification number under which the chemical composition was tested and accepted. The report is to indicate acceptance, or rejection. Appropriate remarks, as necessary, are to be included in the report to clarify conditions of acceptance or rejection.

	All shipments are to be field reported by the district.		All shipments are to be field reported by the district.
Line 38:		Line 38:

	===1124.4.1 Procedure===		===1124.4.1 Procedure===
	Chemical analysis of sodium chloride shall be conducted in accordance with [[106.3.2.32 TM-32, Determination of Purity of Sodium Chloride\|EPG 106.3.2.32 TM-32, Determination of Purity of Sodium Chloride]]. Original test data and calculations shall be recorded in Laboratory workbooks. Test results and field gradation shall then be recorded through ~~SiteManager~~.		Chemical analysis of sodium chloride shall be conducted in accordance with [[106.3.2.32 TM-32, Determination of Purity of Sodium Chloride\|EPG 106.3.2.32 TM-32, Determination of Purity of Sodium Chloride]]. Original test data and calculations shall be recorded in Laboratory workbooks. Test results and field gradation shall then be recorded through AWP.

	===1124.4.2 Sample Record===		===1124.4.2 Sample Record===
	The sample record shall be completed in ~~SiteManager, as described~~ in [[:Category:101 Standard Forms#Sample Record General ~~Information~~\| Sample Record General ~~Information]] [[image:bulldozer.jpg\|20px~~]], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in AASHTOWARE Project (AWP) in accordance with [[:Category:101 Standard Forms #Sample Record, General\|AWP MA Sample Record, General]], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

Smithk at 14:29, 10 December 2018

2018-12-10T14:29:48Z

← Older revision		Revision as of 09:29, 10 December 2018
Line 37:		Line 37:
	To establish procedures for Laboratory testing and reporting samples of sodium chloride for use as a deicer. The requirements are set forth in the bid request issued by MoDOT.		To establish procedures for Laboratory testing and reporting samples of sodium chloride for use as a deicer. The requirements are set forth in the bid request issued by MoDOT.

	===1124.4.1 Procedure===		===1124.4.1 Procedure===
	Chemical analysis of sodium chloride shall be conducted in accordance with [[106.3.2.32 TM-32, Determination of Purity of Sodium Chloride\|EPG 106.3.2.32 TM-32, Determination of Purity of Sodium Chloride]]. Original test data and calculations shall be recorded in Laboratory workbooks. Test results and field gradation shall then be recorded through SiteManager.		Chemical analysis of sodium chloride shall be conducted in accordance with [[106.3.2.32 TM-32, Determination of Purity of Sodium Chloride\|EPG 106.3.2.32 TM-32, Determination of Purity of Sodium Chloride]]. Original test data and calculations shall be recorded in Laboratory workbooks. Test results and field gradation shall then be recorded through SiteManager.

	===1124.4.2 Sample Record===		===1124.4.2 Sample Record===
	The sample record shall be completed in SiteManager, as described in [[:Category:101 Standard Forms#Sample Record General Information\| Sample Record General Information]] [[image:bulldozer.jpg\|20px]], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in SiteManager, as described in [[:Category:101 Standard Forms#Sample Record General Information\| Sample Record General Information]] [[image:bulldozer.jpg\|20px]], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

Smithk: updated link

2018-10-16T13:22:22Z

updated link

← Older revision		Revision as of 08:22, 16 October 2018
Line 3:		Line 3:
	\|'''MGS Information'''		\|'''MGS Information'''
	\|-		\|-
	\|[~~http~~://www.modot.~~mo.gov/business/materials/pdf~~/mgs~~/MGSINDEX.pdf~~ Current General Services Specifications (MGS) By Subject]		\|[https://www.modot.org/general-services-specifications-mgs-subject Current General Services Specifications (MGS) By Subject]
	\|}		\|}

Smithk: updated link

2013-08-22T13:54:15Z

updated link

← Older revision		Revision as of 08:54, 22 August 2013
Line 41:		Line 41:

	===1124.4.2 Sample Record===		===1124.4.2 Sample Record===
	The sample record shall be completed in SiteManager, as described in [~~http~~:~~//contribute.modot.mo.gov/business/materials/pdf/vol_3/AS3510~~.~~pdf Automation Section 3510~~], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in SiteManager, as described in [[:Category:101 Standard Forms#Sample Record General Information\| Sample Record General Information]] [[image:bulldozer.jpg\|20px]], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

Smithk: updated link

2013-02-14T19:50:50Z

updated link

← Older revision		Revision as of 14:50, 14 February 2013
Line 16:		Line 16:

	===1124.2.1 Inspection===		===1124.2.1 Inspection===
	The first shipment per supplier per district on a purchase order shall be sampled and the gradation determined in accordance with [[:category:1001 General Requirements for Material # 1001.4.1 Sieve Analysis\|EPG 1001.4.1 Sieve Analysis]]. If the gradation complies with the requirements of the specifications, a sample shall be submitted to the Laboratory for chemical analysis.		The first shipment per supplier per district on a purchase order shall be sampled and the gradation determined in accordance with [[:category:1001 General Requirements for Material # 1001.5.1 Sieve Analysis\|EPG 1001.5.1 Sieve Analysis]]. If the gradation complies with the requirements of the specifications, a sample shall be submitted to the Laboratory for chemical analysis.

	If the sample fails to meet gradation requirements, two additional samples shall be obtained and tested. Both of the additional samples must meet gradation requirements or the lot represented by the samples will be rejected.		If the sample fails to meet gradation requirements, two additional samples shall be obtained and tested. Both of the additional samples must meet gradation requirements or the lot represented by the samples will be rejected.

Smithk: /* 1124.4.2 Sample Record */ Per CM, updated link to AS 3510

2011-07-05T20:29:04Z

1124.4.2 Sample Record: Per CM, updated link to AS 3510

← Older revision		Revision as of 15:29, 5 July 2011
Line 41:		Line 41:

	===1124.4.2 Sample Record===		===1124.4.2 Sample Record===
	The sample record shall be completed in SiteManager, as described in [http://~~wwwi~~/~~intranet~~/cm/~~materials~~/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in SiteManager, as described in [http://contribute.modot.mo.gov/business/materials/pdf/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

Smithk: /* 1124.4.2 Sample Record */ updated link

2010-07-01T18:18:55Z

1124.4.2 Sample Record: updated link

← Older revision		Revision as of 13:18, 1 July 2010
Line 41:		Line 41:

	===1124.4.2 Sample Record===		===1124.4.2 Sample Record===
	The sample record shall be completed in SiteManager, as described in [http://wwwi/intranet/cm/materials/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[106.9 Reporting ~~Test Results~~\|EPG 106.9 Reporting ~~Test Results~~]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in SiteManager, as described in [http://wwwi/intranet/cm/materials/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

Smithk: updated link

2010-07-01T17:14:41Z

updated link

← Older revision		Revision as of 12:14, 1 July 2010
Line 6:		Line 6:
	\|}		\|}

	This article establishes procedures for inspecting and [[106.5 Sampling\|sampling]] sodium chloride (rock salt) for use as deicing material. The requirements are set forth in the bid request issued by MoDOT.		This article establishes procedures for inspecting and [[106.3 Samples, Tests and Cited Specifications#106.3.1 Sampling\|sampling]] sodium chloride (rock salt) for use as deicing material. The requirements are set forth in the bid request issued by MoDOT.

	Sodium chloride furnished shall arrive at destination in a free-flowing and usable condition and be free from objectionable material.		Sodium chloride furnished shall arrive at destination in a free-flowing and usable condition and be free from objectionable material.

Smithk: /* 1124.4.1 Procedure */ updated link

2010-06-30T19:13:39Z

1124.4.1 Procedure: updated link

← Older revision		Revision as of 14:13, 30 June 2010
Line 38:		Line 38:

	===1124.4.1 Procedure===		===1124.4.1 Procedure===
	Chemical analysis of sodium chloride shall be conducted in accordance with [[106.7.32 TM-32, Determination of Purity of Sodium Chloride\|EPG 106.7.32 TM-32, Determination of Purity of Sodium Chloride]]. Original test data and calculations shall be recorded in Laboratory workbooks. Test results and field gradation shall then be recorded through SiteManager.		Chemical analysis of sodium chloride shall be conducted in accordance with [[106.3.2.32 TM-32, Determination of Purity of Sodium Chloride\|EPG 106.3.2.32 TM-32, Determination of Purity of Sodium Chloride]]. Original test data and calculations shall be recorded in Laboratory workbooks. Test results and field gradation shall then be recorded through SiteManager.

	===1124.4.2 Sample Record===		===1124.4.2 Sample Record===
	The sample record shall be completed in SiteManager, as described in [http://wwwi/intranet/cm/materials/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[106.9 Reporting Test Results\|EPG 106.9 Reporting Test Results]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in SiteManager, as described in [http://wwwi/intranet/cm/materials/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[106.9 Reporting Test Results\|EPG 106.9 Reporting Test Results]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

Smithk: minor clarifications to differentiate EPG articles (that are referenced as "articles", not "sections") from specifications (that are referenced as "sections")

2010-03-31T13:48:25Z

minor clarifications to differentiate EPG articles (that are referenced as "articles", not "sections") from specifications (that are referenced as "sections")

← Older revision		Revision as of 08:48, 31 March 2010
Line 16:		Line 16:

	===1124.2.1 Inspection===		===1124.2.1 Inspection===
	The first shipment per supplier per district on a purchase order shall be sampled and the gradation determined in accordance with [[:category:1001 General Requirements for Material # 1001.4.1 Sieve Analysis\| 1001.4.1 Sieve Analysis]]. If the gradation complies with the requirements of the specifications, a sample shall be submitted to the Laboratory for chemical analysis.		The first shipment per supplier per district on a purchase order shall be sampled and the gradation determined in accordance with [[:category:1001 General Requirements for Material # 1001.4.1 Sieve Analysis\|EPG 1001.4.1 Sieve Analysis]]. If the gradation complies with the requirements of the specifications, a sample shall be submitted to the Laboratory for chemical analysis.

	If the sample fails to meet gradation requirements, two additional samples shall be obtained and tested. Both of the additional samples must meet gradation requirements or the lot represented by the samples will be rejected.		If the sample fails to meet gradation requirements, two additional samples shall be obtained and tested. Both of the additional samples must meet gradation requirements or the lot represented by the samples will be rejected.
Line 38:		Line 38:

	===1124.4.1 Procedure===		===1124.4.1 Procedure===
	Chemical analysis of sodium chloride shall be conducted in accordance with [[106.7.32 TM-32, Determination of Purity of Sodium Chloride\|106.7.32 TM-32, Determination of Purity of Sodium Chloride]]. Original test data and calculations shall be recorded in Laboratory workbooks. Test results and field gradation shall then be recorded through SiteManager.		Chemical analysis of sodium chloride shall be conducted in accordance with [[106.7.32 TM-32, Determination of Purity of Sodium Chloride\|EPG 106.7.32 TM-32, Determination of Purity of Sodium Chloride]]. Original test data and calculations shall be recorded in Laboratory workbooks. Test results and field gradation shall then be recorded through SiteManager.

	===1124.4.2 Sample Record===		===1124.4.2 Sample Record===
	The sample record shall be completed in SiteManager, as described in [http://wwwi/intranet/cm/materials/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[106.9 Reporting Test Results\|106.9 Reporting Test Results]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in SiteManager, as described in [http://wwwi/intranet/cm/materials/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[106.9 Reporting Test Results\|EPG 106.9 Reporting Test Results]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.