Difference between revisions of "Category:710 Epoxy Coated Reinforcing Steel"
Jump to navigation
Jump to search
m (Per Organizational Results, links to reports added) |
m (→710.1 Construction Inspection for Sec 710: updated Research report links) |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 2: | Line 2: | ||
[[image:710.1.jpg|right|125px|thumb|<center>'''Shipping damage'''</center>]] | [[image:710.1.jpg|right|125px|thumb|<center>'''Shipping damage'''</center>]] | ||
[[image:710.2.jpg|left|380px|thumb|<center>'''Epoxy splitting'''</center>]] | [[image:710.2.jpg|left|380px|thumb|<center>'''Epoxy splitting'''</center>]] | ||
| − | Those provisions of [http://modot. | + | Those provisions of [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=11 Sec 706] concerning placement and location of reinforcing steel apply to epoxy coated reinforcing steel. The reinforcing steel should be inspected for damage to the coating. Any damaged areas should be repaired with epoxy patching material furnished by the manufacturer. |
While torch cutting is acceptable to shorten uncoated resteel, in no case should a torch be used on epoxy coated resteel. Any long epoxy bars should be saw cut and the ends patched with patching material approved by the coating manufacturer. | While torch cutting is acceptable to shorten uncoated resteel, in no case should a torch be used on epoxy coated resteel. Any long epoxy bars should be saw cut and the ends patched with patching material approved by the coating manufacturer. | ||
| Line 12: | Line 12: | ||
|'''Structural Steel Coatings''' | |'''Structural Steel Coatings''' | ||
|- | |- | ||
| − | |[ | + | |[https://spexternal.modot.mo.gov/sites/cm/CORDT/or11006_All.pdf Structural Steel Coatings for Corrosion Mitigation, 2010] |
|- | |- | ||
|'''Coated Steel Rebar, Enamel''' | |'''Coated Steel Rebar, Enamel''' | ||
|- | |- | ||
| − | |[ | + | |[https://spexternal.modot.mo.gov/sites/cm/CORDT/or11004.pdf Coated Steel Rebar for Enhanced Concrete-Steel Bond Strength and Corrosion Resistance, 2010] |
|- | |- | ||
| − | |'''See also:''' [ | + | |'''See also:''' [https://www.modot.org/research-publications Research Publications] |
|} | |} | ||
Latest revision as of 13:25, 8 June 2021
710.1 Construction Inspection for Sec 710
File:710.1.jpg Shipping damage
File:710.2.jpg Epoxy splitting
Those provisions of Sec 706 concerning placement and location of reinforcing steel apply to epoxy coated reinforcing steel. The reinforcing steel should be inspected for damage to the coating. Any damaged areas should be repaired with epoxy patching material furnished by the manufacturer.
While torch cutting is acceptable to shorten uncoated resteel, in no case should a torch be used on epoxy coated resteel. Any long epoxy bars should be saw cut and the ends patched with patching material approved by the coating manufacturer.
During placement the inspector should caution the contractor not to damage the coating and make sure the proper vibrators are used.
| Structural Steel Coatings |
| Structural Steel Coatings for Corrosion Mitigation, 2010 |
| Coated Steel Rebar, Enamel |
| Coated Steel Rebar for Enhanced Concrete-Steel Bond Strength and Corrosion Resistance, 2010 |
| See also: Research Publications |
This category currently contains no pages or media.
