Category:172 Maintenance Facility Performance Expectations Environmental Compliance

For additional information or help, the Design Environmental contact may be called at (573) 526-4778.

172.1 Salt Management – Salt Kill

Citation: Missouri Water Quality Standards; Chapter 644 RSMo (Mo Clean Water Law); Federal Clean Water Act

Performance Expectation

Remediate salt kills on and off MoDOT property.

Performance Measure

Identify evidence of dead or stressed vegetation on or off MoDOT property; includes remediated areas where evidence of a salt kill is currently visible. Develop and execute a plan to remove the contamination and reseed the affected area.

Acceptable Solutions

1. Prevent runoff of salt and notify adjacent landowner to offer corrective measures. Contact your district environmental specialist and risk management representative for assistance.

2. Remove soil and replace with clean soil and reseed.

3. Divert runoff from entering the neighbor’s property.

4. Keep all salt and salt mix under cover.

5. Clean up all salt outside and maintain an impervious pad in front of the storage area.

6. Contact the district environmental liaison for additional options.

File:172.1.1.jpg Salt kill on neighbor's property with dead vegetation and trees in background	File:172.1.2.jpg Clean soil replaced contaminated soil and area reseeded
Unacceptable	Acceptable

File:172.1.3.jpg Salt kill on neighbor's property from salt runoff and salt pond leaching and overflow	File:172.1.4.jpg Same area two years later after the salt pond was removed and the soil remediated
Unacceptable	Acceptable

172.2 Salt Ponds and Basins

Citation: Missouri Water Quality Standards; Chapter 644 RSMo (Mo Clean Water Law); Federal Clean Water Act

Performance Expectation

Salt ponds are to be closed and where engineered collection basins are installed they are to be maintained.

Performance Measure

Remove salt pond and dispose of the water in an approved manner. Maintain engineered collection basins and use the water for brine.

Acceptable Solutions

1. Close salt ponds by hauling the water to a permitted publicly owned treatment works (POTW), dig out contaminated soil and dispose of in a permitted solid waste landfill and backfill / grade /seed the area.

2. Engineered salt collection basins have to be maintained by periodic cleaning and resealing.

Note: Salt water can be used to make salt brine if it consists of only water and salt.

File:172.2.1.jpg Leaking salt pond and resulting damage.	File:172.2.2.jpg Same area two years later with grass returning to neighbor's land.	File:172.2.3.jpg Engineered salt basin collects water from salt pad area. The water is used for brine. It is cleaned and resealed every two years.
Unacceptable	Acceptable	Acceptable

172.3 Salt Piles

Citation: Missouri Water Quality Standards; Chapter 644 RSMo (Mo Clean Water Law); Federal Clean Water Act

Performance Expectation

Storm water on maintenance lots shall be protected from salt contamination.

Performance Measure

All salt must be covered and stored to prevent contact with rain or rain runoff.

Acceptable Solutions

1. Salt will be under cover before any precipitation comes in contact with the material.

2. Any salt outside after a snow or ice event has to be cleaned up and returned to the covered area.

File:172.3.1.jpg Salt mix pile stored outside without a cover. Leaching salt, rainwater flows into the bays and stored salt extends beyond the bays.	File:172.3.2.jpg Salt and salt mix stored inside away from moisture. Note that surface water is diverted from the storage building.	File:172.3.3.jpg Salt storage building and impervious pad
Unacceptable	Acceptable Temporary Solution	Acceptable Permanent Solution

File:172.3.4.jpg Adding doors to old salt buildings. These doors are costing $600 to $800 per door.	File:172.3.5.jpg Open end salt tent with tarp cover with sealed mixing pad. The salt is back away from the front.
Acceptable	Acceptable

172.4 Salt Bays and Mixing Pads

Citation: Missouri Water Quality Standards; Chapter 644 RSMo (Mo Clean Water Law); Federal Clean Water Act

Performance Expectation

Protect salt from contact with storm water

Performance Measure

Conduct visual inspection of the storage areas periodically to ensure the salt is kept out of the elements. Maintain the buildings and covers to prevent moisture from coming in contact with the salt.

Acceptable Solutions

1. Discontinue salt bays that do not protect the salt from the elements – construct fabric buildings, domes, tents or other approved buildings.

2. Salt bays still in use shall be maintained in good condition with tarp / door system to protect the material from contact with rainwater and keep salt back away from rain. All mixing pads must be impervious to allow easy cleanup after an event.

3. Re-contour surrounding terrain and direct storm water away from salt storage or relocate salt storage structures if storm water runoff cannot be directed away from structure.

File:172.4.1.jpg Salt doors not closed and salt left outside exposed to the elements	File:172.4.2.jpg Salt doors closed and no salt left exposed to the elements and impervious mixing pad in front for easy cleanup
Unacceptable	Acceptable

172.5 Wash Water

Citation: Missouri Water Quality Standards; Chapter 644 RSMo (Mo Clean Water Law); Federal Clean Water Act

Performance Expectation

Vehicle and equipment washing must be done where the water can be collected and properly treated prior to release to the environment or waters of the state.

Performance Measure

Wash equipment only where the resulting wash water can be contained or treated.

Acceptable Solutions

1. Drive vehicles/equipment to MoDOT lots with appropriate collection systems to wash them.

2. Allow rural facilities to wash vehicles/equipment at commercial truck washes.

3. Covered wash bay with sewer connection or tank system.

4. Install an onsite treatment system. This would require a discharge permit.

5. Construct same for rural facilities and pipe waste water to a holding tank. Wastewater must be removed on a regular basis and transported to nearest public sanitary sewer system. Solids will need to be disposed of at a permitted sanitary landfill. One option could include recirculate the wash water for gross washing followed by clean power wash. All material must be collected.

6. Construct covered wash bay with an oil/water separator and connect to public sanitary sewer system where available and allow rural facilities to use approved MoDOT washing facilities or local commercial wash facilities.

7. Install a zero discharge recirculation system for washing trucks.

Note: Do not discharge to a sewer without notifying the public waste treatment facility.

File:172.5.1.jpg Open wash bay discharging to a ditch and potentially affecting a waterway	File:172.5.2.jpg Washing with fire hose and runoff flowing offsite to a waterway	File:172.5.3.jpg Wash bay connected to a sanitary sewer with an oil/water separator
Unacceptable	Unacceptable	Acceptable

File:172.5.4.jpg Gross salt truck washing enters this engineered pit and is used to make salt brine. In the summer the salt is cleaned up and clean stormwater is diverted around the pit.	File:172.5.5.jpg Floor drains and wash bay are connnected to a collection tank that is pumped and the water treated at a wastewater treatment plant.
Acceptable	Acceptable

File:172.5.6.jpg District truck wash connected to a sanitary sewer	File:172.5.7.jpg New truck wash under construction and connected to a sanitary sewer. Walls and roof to be installed.
Acceptable	Acceptable

172.6 Storm Water

Citation: 10 CSR 20-7.015 & 10 CSR 20-7.031, Chapter 644 RSMo; 10 CSR 20-7.031(3) (Water Quality Standards) Missouri Clean Water Law - Permit and Water Quality Regulations (No Discharge Permit); Federal Clean Water Act

Performance Expectation

Storm water from maintenance facilities needs to be controlled to prevent aggregate, silt and sediment from being washed off the property into ditches and waterways.

Performance Measure

Inspect all areas on the maintenance lot where storm water potentially leaves the facility and develop and implement a plan to control the runoff.

Acceptable Solutions

1. Evaluate problem and implement facility improvements to keep silt, rock, aggregate and other materials on the lot at locations where storm water flows off-site. For example: install an aggregate berm that allows storm water to flow through, but contain aggregate material from migrating offsite. If this is the chosen option, these structures must be constructed in such manner that they do not retain water, but will catch sediment and can be maintained. Use mixture of fines and course material that will slow down the storm water for material to settle.

2. Install grass buffers that are sufficient to catch material and filter storm water runoff. Install so they can be maintained.

File:172.6.1.jpg Rock-lined ditches and grass berms work well but need to be maintained. Ditch checks that can be cleaned out would aid this operation.	File:172.6.2.jpg This berm hold the water long enough for the silt and suspended particles to settle and can be easily cleaned. It dries out between rains.
Unacceptable unless maintained	Acceptable

File:172.6.3.jpg Ditch check that can be cleaned and maintained	350px
Acceptable	Example of the ditch check design

File:172.6.5.jpg Grassed area and rock apron	File:172.6.6.jpg Add or increase green space around lots
Acceptable	Acceptable

172.7 Secondary Containment for Brine

Citation: Sections 10 CSR 20-7.015, 10 CSR 20-7.031, Chapter 644 RSMo; Missouri Clean Water Law and Regulations (Construction and Operating Permit); Federal Clean Water Act

Performance Expectation

Keep all snow control chemicals (brine, beet juice (Geomelt) and calcium chloride) from entering waterways. Though not required by law, a release of the material to the environment would be regulated and could result in a major cleanup expense.

Performance Measure

Place all storage tanks, pumps and plumbing inside watertight secondary containment. Check tanks and pumps for integrity.

Acceptable Solutions

1. Berm of clay, concrete, synthetic liner or impervious material with drainpipe and closed lockable valve.

2. Locate snow control chemical tanks including pumps and plumbing inside existing buildings where available and provide secondary containment.

3. Construct secondary containment structure for snow control chemical tanks including pumps and plumbing.

File:172.7.1.jpg Sealed secondary containment but the pump is outside	File:172.7.2.jpg Sufficient secondary containment
Unacceptable - everything needs containment	Acceptable

172.8 Hazardous Waste Disposal

Citation: 40 CFR Subchapter I, Federal Hazardous Waste Management Law; Sections 260.350 to 260.430 RSMO; 10 CSR 25 Chapter 5 (Rules Applicable to Generators of Hazardous Waste)

Performance Expectation

Ensure that all the materials are usable and do not become “waste”, which would create an environmental liability.

Performance Measure

Identify unusable materials and chemicals and contact your district environmental point person and environmental specialist for proper handling or disposal. Contact your district environmental specialist to assist with materials that cannot or will not be used at a MoDOT facility.

Acceptable Solutions

1. Control Inventory – order only one to two years worth of materials.

2. All containers storing unknown material should be sampled and characterized for proper handling and disposal by an environmental specialist.

3. If usable material (chemicals, paints, etc.) cannot be used at a lot, it should be shared with or given to another MoDOT facility that can utilize the materials.

4. All known or unknown materials not currently used (chemicals, paints, etc.), which cannot be used by other MoDOT facilities or that are out-of-date and no longer usable, must be disposed of at a permitted hazardous waste disposal facility (contact your district environmental specialist for assistance).

5. Do not move hazardous waste to another location (contact your district environmental specialist for assistance).

Note: Do not dump any product on the lot to dispose of the material. Refer to the MoDOT “Environmental Standard Operating Procedures for Sale of MoDOT Property” for guidance when selling excess materials or chemicals.

File:172.8.1.jpg Drums of material improperly stored and not all containers are labeled	File:172.8.2.jpg Drums properly labeled and stored on secondary containment	File:172.8.3.jpg Inventory control is a must to reduce the amount of waste generated
Unacceptable	Acceptable	Acceptable for district distribution

172.9 Drains

Citation: 10 CSR 20-6.010 Missouri Clean Water Law and Regulations (Construction and Operating Permit)

Performance Expectation

Facilities with floor drains in the maintenance bays that are not plumbed to a public sewage system shall be closed to prevent water from entering the environment or corrected with a connection to an approved alternative.

Performance Measure

All systems not connected to an approved holding tank or public sewage system must be closed.

Acceptable Solutions

1. Connect all floor drains to an oil / water separator and public sanitary sewer system where possible. For facilities where floor drains are not connected to a public sanitary sewer system, the facility must plug, seal or otherwise prevent discharge from the floor drains.

2. Connect floor drains to a holding tank and have contents removed by waste hauler.

3. An oil/water separator can be used as a holding tank or prior to a holding tank.

File:172.9.1.jpg Floor drain discharges to road ditch	File:172.9.2.jpg Floor drain plugged and cleaned out by septic hauler
Unacceptable	Acceptable

172.10 Spill Prevention Control Countermeasure (SPCC)

Citation: U.S. Environmental Protection Agency (EPA) Regulations, Facility Diagram and Description

Performance Expectation

All maintenance lots with 1,320 gallons of petroleum, animal or vegetable oil products storage capacity are required to have and maintain an SPCC plan at their facility.

Performance Measure

Bring all plans into compliance by updating the plan to fit the facility. Every five years a professional engineer reviews, signs, and stamps the plans. A link for tools to assist with SPCC plan development is available.

Possible Solutions

1. Provide security measures for your facility; this includes adequate lighting, gating and fencing.

2. All petroleum and oil-based material containers 55 gallons or greater must have secondary containment.

3. Containers with double walls need containment for the pumps and plumbing for the contents of the container.

4. Maintain annual personnel training and monthly facility inspections.

5. Maintain equipment, tanks and containment to prevent spills.

File:172.10.1.jpg No fence in front though there was barbed wire fence on other three sides	File:172.10.2.jpg This site was fenced on all four sides with chain link fence
Unacceptable	Acceptable

File:172.10.3.jpg Clean containment, painted tanks, locked valves and covers, smaller tank properly closed with date on label and tanks off the floor of the containment. The date and amount of water drained is to be recorded in the SPCC plan	File:172.10.4.jpg All trash and debris should be cleaned out and properly disposed of and be sheen absorbed off the water before it is drained
Acceptable	Unacceptable

250px	File:172.10.6.jpg Cable fencing system	File:172.10.7.jpg Lockable gates
Unacceptable	Acceptable	Acceptable

172.11 SPCC and Various Statewide Issues

Citation: U.S. Environmental Protection Agency (EPA) Regulations, Solid Waste Management Law in Sections 260.200 through 260.345 RSMo, Facility Diagram and Description

Performance Expectation

Keep all materials organized and the facility clean of debris.

Performance Measure

Perform routine inspections to identify problem areas. Maintain training to keep in compliance with SPCC regulations

Requirements

1. Maintain the spill kits and store them near fuel islands for easy access during on-site spill events.

2. When any petroleum tank is taken out of service, it should be label “Closed”, with date of closure, and valves and ports are to be closed and locked. See picture in SPCC section.

3. Asphalt hoses need collection or containment rather than being allowed to drain onto the ground.

4. Facilities with oil/water separators need to have these scheduled for regular clean out.

5. Parts washing solvent should be converted to the Zep® solvent or other non-hazardous equivalent.

File:172.11.1.jpg Keep absorbent in a convenient location	File:172.11.2.jpg Plug floor drains not connected to a public wastewater treatment plant
Acceptable	Acceptable

File:172.11.3.jpg Proper solid waste storage. Area is picked up, waste is segregated, area clean and easily maintained with walls and floors	File:172.11.4.jpg Drum properly labeled and stored in secondary containment. Need to protect the labels
Acceptable	Acceptable

File:172.11.5.jpg The hose drains into the conrete containment and cleaned up for use as product or it can be collected in a bucket or drum to be used as intended	File:172.11.6.jpg Maintained collection basin system that provides secondary containment	File:172.11.7.jpg Earth berm for tank and distributor
Acceptable	Acceptable	Acceptable

172.12 SPCC and Portable Tank Storage

Citation: U.S. Environmental Protection Agency (EPA) Regulations, Facility Diagram and Description

Performance Expectation

When a portable tank is in storage for future use it must be in secondary containment.

Performance Measure

Perform routine inspections of portable tanks to identify problem areas. Maintain training to keep in compliance with SPCC regulations.

Requirements

1. Containment must be large enough to hold the volume of the tank if stored inside and large enough to hold the volume plus a 25-year rain event if stored outside. Even if the tank is empty it must be in containment.

2. Containment must be made of material compatible with the tank contents and impervious to leakage in the event of a leak until it can be cleaned up.

3. The tank must be kept painted and visually inspected for rust and damage.

4. If a portable tank is taken out of service, it should be label “Closed”, with date of closure, pumps removed, and valves and ports are to be closed and locked.

Outside a vehicle requires secondary containment	In use in vehicle no secondary containment required
Unacceptable	Acceptable

If it is going to be closed it needs to have the pump and valves removed and all fill ports	The tank needs to be placed into secondary containment and it can be placed on a rack in secondary containment to avoid using containment
Unacceptable	Acceptable